Marine audio built for open water — speakers, amplifiers, subwoofers and tower systems, supplied and fitted at Crews Inn Marina.
Tower speakers
Wake-tower speakers are sold in pairs and are built to project sound a long way behind and beside the boat.
-
REV 8 and REV 10 (V2)
The core Revolution tower speaker, in 8″ and 10″ sizes with a gloss finish.
The Revolution (REV) Series is Wet Sounds' main wake-tower speaker. Each pair uses a Kevlar-reinforced woofer with a titanium horn-loaded compression driver, which is a tweeter coupled to a horn so it carries clearly at distance.
The 8″ suits smaller towers where space is tight; the 10″ gives more midbass and projection. Both come in gloss black or gloss white, and the clamp style is chosen when ordering: swivel, fixed, silver aluminium fixed or X-Mount for flat surfaces. They pair with an external amplifier, and RGB LED ring kits are available separately for lighting.
-
REV 410 (V2)
A dual 10″ tower speaker for large boats needing the most coverage.
The REV 410 is the largest speaker in the Revolution range, using two 10″ drivers with horn-loaded compression technology in a single enclosure. It is aimed at big wake and surf boats and open-water use where the music has to carry well beyond the boat.
It is listed in white. Mounting choices are an X-Mount surface mount system, a TC3-FC fixed clamp with built-in wiring, or a TC3-SC swivel clamp that can be released with a single bolt. A 6-pin connector option carries speaker and LED wiring through the clamp. It needs a suitably powerful external amplifier to match its size.
Finish White -
REV Special Edition (SE)
Revolution 8″ and 10″ in matte black or matte white, for marine and powersports.
The REV Special Edition uses the same driver approach as the standard REV, a Kevlar-reinforced woofer with a titanium horn-loaded compression driver, but in matte finishes. Wet Sounds describes it for both marine and powersports use.
It comes in 8″ and 10″ sizes, in matte black or matte white, so it suits boats where a gloss finish does not fit the look. Clamp or X-Mount style is selected when ordering, as with the standard REV. It is sold as a pair and needs an external amplifier. If you want the standard gloss finish instead, see REV 8 and REV 10.
-
REV HD
The top Revolution tower speaker: a 10″ or 12″ HD driver with front and rear RGB lighting.
REV HD is described as the next step on from the standard Revolution Series. It pairs a 10″ or 12″ HD driver with a coaxially mounted titanium horn-loaded compression driver, and it has RGB LED rings front and rear plus an illuminated badge.
The grille and clamp are bought separately, which lets you tune the look: XZ, XW or XS grilles in black or white, and swivel, fixed or X-Mount mounting. Choose the 12″ for the most bass from a tower, or the 10″ where weight and tower space matter. Neoprene SuitZ covers are available to protect the speakers when trailering. Use an external amplifier and a compatible RGB controller to run the lighting.
-
ICON 8 (V2)
A compact tower speaker with an 8″ driver in a housing about the size of a 6.5″ tower speaker.
The ICON 8 packs an 8″ continuous-cone midbass driver and a 1″ titanium tweeter, mounted in the grille, into a housing Wet Sounds compares to a typical 6.5″ tower speaker. It suits cruising, anchoring and wake surfing where a smaller footprint is wanted.
It is a high-gloss, UV-inhibited composite enclosure with stainless steel hardware, sold as a pair with mounting clamps included. Choose black or white, then the clamp style: swivel, swivel base, fixed, silver fixed or X-Mount. It is a step below the REV range in size and output, so it is a good fit for smaller towers and moderate systems.
-
RECON 6 POD
A 6.5″ coaxial speaker in a tower pod with RGB grilles, for tube or surface mounting.
The RECON 6 POD is a 6.5″ coaxial speaker in a pod enclosure that clamps to tubes up to 2″ in diameter or mounts to a surface. It has a 1″ titanium dome tweeter and RGB-lit grilles.
Wet Sounds positions it as a low-power-friendly upgrade that works with factory head units or entry-level amplification, rated at up to 120W per speaker. It is the smallest and simplest route to tower sound in this range. If the boat needs more output or range behind the boat, step up to ICON 8 or REV. Choose the XS silver grille or the XW white grille. An RGB controller is needed to change the lighting colours.
Tell us your tower tube diameter and boat make so we can match the clamp or bracket to the speaker.
Coaxial speakers
Round and rectangular speakers that fit into a panel, bulkhead or wake-tower pod, grouped by Wet Sounds series.
-
SCOUT 6 and SCOUT 6 RGB
The entry-level 6.5″ coaxial, with or without built-in RGB lighting.
SCOUT is the simplest coaxial speaker in the Wet Sounds range: a 6.5″ high-efficiency design intended as a drop-in upgrade for factory systems, running directly from a head unit or a small amplifier. It is rated at 30W RMS.
The SCOUT 6 RGB adds RGB LEDs behind a textured multi-spoke grille, which need a compatible RGB controller to change colour. Both come in dark titanium or white. Choose SCOUT where budget and simple fitting matter most, and step up to RECON, REVO or ZERO if you want more power handling or a larger driver. It suits boats and side-by-side vehicles.
-
RECON 6
A 6.5″ coaxial that works well with factory head units and low-power systems.
RECON is the efficient, lower-power coaxial range. The 6.5″ model pairs a midrange driver with a small aluminium dome tweeter and is designed to sound good from a factory head unit or a modest amplifier; Wet Sounds says it performs with as little as 60W.
Choose between the XS silver grille and the XW white grille, with or without RGB lighting. The non-RGB version suits a clean look; the RGB version needs a compatible controller to change colour. Step up to REVO for higher power handling, or ZERO if mounting depth is the constraint.
-
RECON 8
The 8″ RECON coaxial, for more bass than a 6.5″ in the same efficient range.
The RECON 8 gives the efficient RECON sound in an 8″ size, with a larger midrange driver for more midbass and a high-output aluminium dome tweeter. It is described for marine and powersports use and works with a wide range of audio systems rather than needing a large amplifier.
It is listed with RGB-lit grilles in XS silver, XW white and XS black. Choose it for a boat with an 8″ opening or tower pod where you want a step up in bass without moving to the more powerful REVO or ZERO ranges. A compatible RGB controller is required for lighting.
-
REVO 6 (V3)
A high-output 6.5″ marine coaxial with a choice of grille styles and finishes.
REVO is the higher-power coaxial series. The 6.5″ model uses a Conex spider, Santoprene surround and a heavy-duty Nylas composite frame, which are materials chosen to resist moisture and UV.
It is offered with the XS stainless steel grille in black, white, silver or gunmetal, the XW grille in black or white, or the SW grille in black or white. It suits wake boats, ski boats, centre consoles, pontoons and side-by-sides. Compared with RECON it handles more power, so it is the better pairing with a dedicated multi-channel amplifier rather than a factory head unit.
-
REVO 8 (V3)
The 8″ REVO coaxial with RGB-lit grilles in the same finishes as the 6.5″.
The REVO 8 is the 8″ version of the high-output REVO coaxial, built around an 8″ mid driver and a 1″ titanium high-output tweeter, with integrated RGB backlighting. It uses the same weather-resistant construction as the 6.5″ model.
It is available with XS stainless steel grilles (silver, black, white or gunmetal), XW grilles in black or white, and SW grilles in black or white. An RGB controller is sold separately. Choose it when you have an 8″ opening, for example in a boat bulkhead or a tower pod, and want more midbass than the 6.5″ gives.
-
REVO CX-10 (S2)
A 10″ coaxial, the largest in the REVO range.
The CX-10 is described as the largest coaxial in the REVO lineup. It has a 10″ high-output mid driver with a 1.25″ titanium dome tweeter, and RGB-lit grilles.
It is for boats with a large opening that want strong projection in open air without moving to a tower speaker. Grille choices are SW and XW in black or white, and XS stainless in silver, black, white or gunmetal. A compatible RGB controller and an external amplifier are needed. If you have a smaller opening, REVO 8 or REVO 6 use the same grille options.
-
ZERO 6.5″ and 8″ coaxial
Shallow-mount high-output coaxials, built to bring REV tower sound into tight spaces.
The ZERO Series is designed to bring the character of the REV tower speakers into places where mounting depth is limited. It has a horn-loaded tweeter, an oversized neodymium motor and a composite cone with a Nomex aramid spider.
The 6.5″ and 8″ sizes come with XZ grilles in black or white, or XY "yacht style" white mesh grilles for a more refined look. Wet Sounds lists them for marine, powersports and motorcycle use. Choose ZERO over REVO where a shallow cavity or a space-constrained dash is the issue. LED ring kits are available for the ZERO range.
-
ZERO 5x7 and 6x9
ZERO coaxials in rectangular sizes, for 5x7 and 6x9 factory-style openings.
These ZERO speakers use the same high-output construction as the round ZERO models but in 5x7 and 6x9 shapes, intended for tight OEM and custom installs where a round speaker will not fit.
The 5x7 is shallow-mount with a grille-less design for a clean OEM-style finish and comes with XZ black grilles. The 6x9 is listed with XZ black or XZ white grilles. Choose these when you are replacing a rectangular factory speaker. Shallow mounting depth makes them useful in panels, doors and consoles with little space behind.
-
ZERO 6 component set
A 6.5″ component set with a separate woofer and tweeter for better imaging.
Unlike the coaxial ZERO speakers, the ZERO 6 CS-B is a component set: a 6.5″ woofer plus an independent horn-loaded tweeter with a PEN diaphragm. Because the tweeter is separate, it can be aimed and placed on its own, which helps sound staging and imaging, meaning how well the music seems to come from in front of you rather than from the speaker.
It suits installs where you want the best clarity from a compact 6.5″ system and can fit the separate tweeter in a dash or panel. The black version is listed. If you only need a drop-in replacement without separate tweeter placement, the coaxial ZERO 6 is simpler.
The grille letters (SW, XW, XS, XZ, XY) describe the grille style, and the suffix is the colour. Give us the cut-out size and the finish you want and we will match the model.
Shallow and surface-mount speakers
Speakers for places with little depth behind the panel, or for surface mounting under gunnels and in towers.
-
WS-SWM-600
An ultra-shallow 6.5″-class speaker for panels with very little depth.
The WS-SWM-600 is a full-range shallow-mount speaker with a mounting depth of just 0.83″ (21 mm). Its 5.12″ (130 mm) cut-out is meant to retrofit into most standard 6.5″ openings, so it can replace an existing speaker without enlarging the hole.
It is designed for marine and powersports installs where there is almost no room behind the panel, such as thin hull liners, doors or consoles. Where depth is not a problem, the REVO or RECON coaxials offer more output and a wider choice of grilles. It needs an amplifier or head unit with speaker outputs to drive it.
-
REV 5x7 SM-W
A white 5x7 surface-mount horn-loaded speaker in a rotomoulded enclosure.
The REV 5x7 SM-W is a surface-mount speaker built around a 5x7 horn-loaded compression driver in a marine-grade rotomoulded enclosure. A horn-loaded driver uses a horn to focus the sound, which helps it carry in open air.
It suits applications where space is tight but you still want strong output and good projection. The integrated enclosure allows flexible surface-mount placement without cutting a hole, and Wet Sounds mentions under-gunnel installs as a good fit. It is white only. Choose it when you want REV-style sound in a small box. It needs an external amplifier for best results.
-
REV 696 RS
A raw 6x9 Pro-Axial driver for upgrading existing wake-tower enclosures.
The REV 696 RS is a 6x9 Revolution Series driver sold without an enclosure. It is intended for wakeboard tower enclosures that already accept a 6x9 speaker, letting you upgrade their output while keeping the existing housing and clamps.
Pro-Axial means the tweeter sits on the same axis as the woofer, in the same way as a coaxial speaker. Check that your tower enclosure takes a 6x9 driver before ordering, because it is not a complete speaker. If you need a full speaker with a housing and clamps, the REV tower speakers are the better choice, and an external amplifier will be needed either way.
-
WS-TW-100
A pair of 1″ titanium-dome tweeters to add high-frequency detail.
The WS-TW-100 is a pair of 1″ titanium-dome marine tweeters. A tweeter handles the highest frequencies, such as cymbals and vocal clarity, and these can be added alongside a woofer or coaxial speaker that needs a brighter top end.
They are a small add-on rather than a complete speaker system, so they are chosen as part of a larger design. They suit installs where a separate tweeter can be placed in a dash, panel or pillar. Let us know which speakers they are going with and where they will be mounted so we can confirm they suit the setup and the wiring needed.
-
Venue Series VS-SMC-65
A weather-resistant 6.5″ shallow-mount speaker for permanent outdoor installs.
The Venue Series VS-SMC-65 is listed in Wet Sounds' marine range but is described for landscape and architectural installs, where speakers stay outdoors permanently. It is a shallow-mount 6.5″ speaker with a weather-resistant build against moisture, UV and temperature swings.
It suits covered decks, pavilions, pool areas and dockside spaces rather than a moving boat, and it is meant for continuous outdoor use at home or in commercial spaces. Shallow-depth mounting makes it practical for ceilings and soffits. It needs an amplifier. Tell us about the location and we can confirm whether it is the right model or a marine coaxial would suit better.
Measure the cut-out and the free depth behind the panel before choosing.
Subwoofers
Marine subwoofers are grouped by how they mount: free-air, ported, dual-voice-coil high-output, or sealed.
-
REVO FA (free-air)
Free-air subwoofers that need no enclosure, in 8″, 10″ and 12″.
REVO FA subwoofers are designed for free-air or infinite-baffle installs, which means the mounting surface itself acts as the enclosure, so no box is needed. That makes them useful for factory upgrades and tight spaces. They have a Nylas composite frame and an injection-moulded composite cone built for moisture and UV.
They come in 8″ (4Ω), 10″ (2Ω or 4Ω) and 12″ (2Ω or 4Ω), all in black. Grilles are sold separately in SW, XW and XS styles in several colours, and RGB kits are available. Choose FA where there is no room for a box; step up to HP if you have a ported box.
Finish Black -
REVO HP (high power)
High-power 10″ and 12″ subwoofers tuned for ported enclosures.
REVO HP subwoofers are optimised for ported enclosures, where a tuned vent gives more output and efficiency than a free-air mount. They have stainless steel terminals and updated rear venting to help manage heat.
They are available as a 10″ 4Ω and a 12″ 4Ω, in black. They are the right driver for a properly designed ported box, and the 12″ also forms the active part of the REVO 12 PSE enclosure system. Choose HP when you want more output than the FA range and have space for a proper enclosure. They need a subwoofer amplifier that suits a 4Ω load.
-
REVO XXX V4
Extreme-output dual-voice-coil subwoofers in 12″ and 15″.
The REVO XXX V4 platform is aimed at maximum low-frequency output. It is built to handle very high continuous power, with a motor and cooling design intended to control heat during long, loud playback.
The 12″ and 15″ models are black, with dual 2Ω voice coils. A dual voice coil sub has two coils that can be wired together in different ways to suit the amplifier. They are for competition-style or very bass-heavy systems on larger boats and need serious amplification, such as a monoblock from the Sinister range. For everyday systems the HP or ZERO subs are usually more practical and easier to fit.
-
RECON 10 FA
A 10″ free-air subwoofer in the efficient RECON range.
The RECON 10 FA is a 10″, 4Ω free-air subwoofer for infinite-baffle installs, where the mounting surface acts as the enclosure so no box is needed. It has a Nylas composite frame, a composite cone and a Santoprene spider for marine use.
It comes with a grille included, either XS silver or XS black. Choose it as a straightforward free-air option when you want a 10″ sub without building or buying a box, for example on a boat with a suitable bulkhead or panel. For more output or more grille choices, see the REVO FA or REVO HP subwoofers.
-
ZERO sealed subwoofers
Shallow-mount 10″ and 12″ subs designed for sealed enclosures.
ZERO subwoofers are built for sealed enclosures in space-constrained installs, combining a shallow mounting depth with a rigid composite cone and TPR surround. A sealed box gives tight, controlled bass without needing a large air volume.
They come in 10″ and 12″, in 2Ω or 4Ω, with XZ grilles in black or white. They are the subwoofers supplied in the ZERO sub enclosure kits. Choose them when depth and space are limited and you want controlled bass rather than the loudest possible output. Match the 2Ω or 4Ω choice to your amplifier, and use the matching enclosure if you do not already have a box.
Impedance (2Ω or 4Ω) must match the amplifier channel, so tell us the amplifier you plan to use.
Subwoofer enclosures
Ready-made boxes and powered units, so you do not need to build or tune an enclosure.
-
STEALTH AS powered enclosures
All-in-one powered subwoofer boxes in 8″ and 10″.
The STEALTH AS units combine a subwoofer and a sealed Class-D amplifier in one moulded polyethylene enclosure. That makes them a simple add-on bass solution when you do not want to run a separate amplifier and box.
They come in 8″ and 10″ sizes. They are built for marine and powersports use, and the amplifier is sealed against moisture and debris. Choose one if you want to add bass to a basic system with minimum wiring; they need a power feed and a signal input from your head unit or amplifier. For more output, a separate sub and amplifier gives more flexibility.
-
ZERO sub enclosure kits
Rotomoulded enclosures with a ZERO subwoofer included, in 10″ and 12″.
These kits supply a weatherproof rotomoulded enclosure together with a ZERO Series subwoofer. The enclosure is built to reduce flex, using a structural support behind the woofer mounting area, which helps keep the bass consistent.
They come in 10″ and 12″, each with a 2Ω or 4Ω subwoofer. They are for boats where you want a complete, ready-to-connect sealed sub setup without sourcing the box and driver separately. Choose 2Ω or 4Ω to match your amplifier. The ZERO range is designed for compact, shallow installs, so these suit boats where space is the main constraint.
-
REVO 12 PSE
A passive-radiator enclosure pairing a REVO 12 HP with a passive radiator.
The REVO 12 PSE combines an active REVO 12 HP subwoofer with a 12″ passive radiator in a rotomoulded, fully sealed enclosure. A passive radiator is a second cone with no motor that moves with the air pressure, and Wet Sounds says the result gives output characteristics of a ported system while staying sealed.
It is pre-wired with weatherproof speaker and RGB-ready connections, so installation is simpler. A range of grille styles is offered when ordering. Choose it where you want strong bass and a tidy sealed box with the connection work already done, and size the amplifier for a REVO 12 HP.
Size 12″ -
Ported 12 ENC
A rotomoulded ported box for select Wet Sounds 12″ subwoofers.
The Ported 12 ENC is a heavy-duty rotomoulded ported enclosure with tuned ports to boost low-frequency output. It has a weatherproof 2-pin connector and marine-grade construction intended to cope with moisture, vibration and temperature changes.
It is for select Wet Sounds 12″ subwoofers, so check the match with us before ordering. Ported boxes give more output than sealed ones but take more space and are less tight in their response. It is a good fit for boats where there is room to mount a larger box and you want maximum bass from a 12″ driver, paired with a suitable subwoofer amplifier.
-
WS-SUB 650 ES
A compact slim ported 6.5″ subwoofer enclosure system.
The WS-SUB 650 ES is a slim rotomoulded ported enclosure with a 6.5″ subwoofer, meant for places where a regular subwoofer will not fit. Wet Sounds describes it for marine, powersports and recreational vehicle installs.
Its compact form allows installation in tight spots where there is little room, and the ported design is intended to produce strong, controlled bass for its size. It is the smallest bass option in the range. Choose it when space is the main constraint and you want to add low end to a small system, using a suitable amplifier to drive it.
Enclosure choice follows the subwoofer you want, so confirm the driver size first.
Amplifiers
Class-D marine amplifiers in several series, from compact monoblocks to eight-channel systems.
-
HTM Series
Full-range Class-D amplifiers from 1 to 8 channels, with selectable crossovers.
The HTM Series are compact, full-range Class-D amplifiers for demanding marine and powersports use. Class-D is an efficient design that draws less current and runs cooler. They have selectable crossovers (high-pass, low-pass or full range), so each channel can be set to suit a speaker or a subwoofer.
The range covers mono (HTM-1), 4-channel (HTM-4), 6-channel (HTM-6) and 8-channel (HTM-8) versions. The eight-channel is useful for multi-zone boats with many speakers. Pick the channel count by adding up the speakers and subs you want to run, and ask us if you would like help working out the best combination.
-
HTX-2
A compact Class-D 2-channel amplifier.
The HTX-2 is a 2-channel Class-D stereo amplifier in a compact, marine-grade case, with low current draw and good thermal efficiency. It suits boats and powersports vehicles with demanding conditions such as water exposure and vibration.
It is used to power a single pair of full-range speakers, which makes it a simple choice for a basic system, or a stepping stone for adding amplification to a factory setup. For larger systems with more speakers or a subwoofer, use the HTM, SYN or Sinister ranges, which offer more channels and different power levels.
-
SYN-DX (Syndicate Series)
Compact Class-D amplifiers in 2, 4 and 6-channel versions, plus a high-power 2-channel.
The Syndicate (SYN-DX) Series is a Class-D range aimed at clean, efficient power in a compact chassis, with reduced current draw. Channels can be used for full-range speakers, multi-zone systems or bridged, which means two channels combined into one for extra output.
The range includes the SYN-DX2 and the SYN-DX2.3 HP (a higher-power 2-channel), the SYN-DX4 and the SYN-DX6. The compact footprint helps in boats where space is limited. Choose the channel count from the number of speakers, and the HP version where a 2-channel needs extra power. It sits between the HTX-2 and the Sinister range.
-
Sinister SDX
High-output Class-D amplifiers with a cast aluminium chassis and MAXED power supply.
The Sinister SDX range uses Wet Sounds' Class-D design with its MAXED power supply, which aims to lower current draw and heat so the amplifier strains the boat's electrical system less. The amplifiers use a full cast aluminium chassis.
Models are the SDX2 (2-channel), SDX4 (4-channel), SDX6 (6-channel) and the SDX2500 monoblock for subwoofers. Use the SDX2500 for large subwoofers such as the REVO XXX, and the multi-channel units to run tower and in-boat speakers. This is the range for larger or louder systems where efficiency under load matters.
-
STX MICRO-1
A very small Class-D monoblock for subwoofers in tight spaces.
The STX MICRO-1 is an ultra-compact Class-D mono amplifier in a sealed die-cast aluminium chassis that resists water, dirt and vibration. A monoblock has one channel and is normally used for a subwoofer. It is designed for tight installs on ATVs, UTVs and boats.
It can be mounted behind panels, under seats or in storage compartments. Choose it for a small subwoofer where a full-size amplifier will not fit. For larger subwoofers or louder systems, the Sinister SDX2500 or HTM-1 monoblocks are more suitable options.
Tell us the number of speakers and subs, and we will match the channel count.
Media centres and receivers
Marine head units with Bluetooth and radio, built for the helm and sealed against the weather.
-
WS-ZX-MC-20
A 3-zone marine media centre with a colour display.
The WS-ZX-MC-20 is built on the WS-MC-20 platform and adds three independent audio zones through a ZONE X selector, for example bow, helm, cabin, tower or a subwoofer zone. It has a 3.0″ colour display with album art and a rotary encoder, which is a turn-and-press control knob.
It supports AM/FM/Weather Band radio and Bluetooth. It is the choice for larger boats with several areas that need separate control. A matching wired transom remote and an NMEA 2000 adapter are available as add-ons. A flush-mount kit is also listed for the MC-20 range.
-
WS-MC-5 V2
A compact AM/FM/Bluetooth media centre with preamp outputs and onboard amplification.
The WS-MC-5 V2 is a low-profile source unit for entry-level and mid-tier systems. It has Bluetooth streaming, dedicated preamp outputs and onboard amplification, so it can power a basic set of speakers by itself or feed external amplifiers later.
It fits into tight helm locations, dash panels or custom enclosures, and a flush-mount kit is available. It supports standalone use as well as multi-zone expansion. Choose it for a simple boat system where space is limited and you want the option to grow the system later, and pick the WS-MC-2 instead if you want satellite radio support.
-
WS-MC-2
A compact media centre with SiriusXM compatibility and Weather Band.
The WS-MC-2 is a compact head unit with AM/FM and Weather Band, SiriusXM compatibility, Bluetooth, USB and auxiliary input, plus Pandora compatibility. Weather Band gives access to broadcast weather alerts.
It suits small helms and space-constrained installs on boats and powersports vehicles. A flush-mount kit, a replacement face cover and a wired transom remote are available for it. Choose it when you want satellite radio support in a compact unit. If you want a digital tuner rather than SiriusXM, the WS-MC-5 V2 is the alternative in the same size class.
-
WS-MC-RND
A round media centre sized for a standard gauge opening.
The WS-MC-RND is a round head unit that fits a standard gauge opening, with a 2.75″ LCD, large backlit buttons, Bluetooth, auxiliary input and a USB charging port. It has a 4x25W at 4Ω built-in amplifier and two preamp outputs.
Choose it when the dash has a round gauge hole free and you want a clean, factory-style look rather than a rectangular head unit. The built-in amplifier can run a basic set of speakers directly, and the preamp outputs let you add external amplifiers for a larger system later.
Tell us how many zones you need and whether the boat has NMEA 2000.
Controllers, remotes and signal
Small controllers, transom remotes and signal accessories for adding Bluetooth and extra control points.
-
Bluetooth controllers
Small Bluetooth controllers in knob, rocker, dual-zone and universal receiver forms.
Wet Sounds makes several compact Bluetooth controls. The WW-BT VC-V2 has a single knob for play, pause, skip and volume; the WW-BT-RS is a rocker-switch version with volume; the WWX-DZ-BT is a dual-zone controller; and the WW-BT UR is a universal receiver with no controls, which is operated from the phone.
The knob controller mounts flush in-dash or under-dash. These suit boats with an amplifier but no head unit, or where you want simple Bluetooth control. Choose by how you want to operate it and how many zones you have.
-
Transom remotes
Wired and NMEA remotes to control a media centre from the transom or elsewhere.
Transom remotes let you control the music from the swim platform or other spots away from the helm. Models include the MC-TR and MC-TR MINI (for the MC-1 and MC-2 units), the WS-G2-TR and the colour-display WS-G2-CTR (for the WS-MC-20), the WS-ZX-CTR (for the ZX-MC-20) and the WS-NMEA-TR, which works over a NMEA 2000 network with the MC-20.
Extension cables and Y-cables are available to add more remotes or reach further. Tell us your head unit and we will match the right remote and cable.
-
Signal and system accessories
Wireless audio, talk-back microphone, line driver and EQ mounts.
This group covers the A-Link Plus wireless send/receive kit (using SKAA wireless technology), the WS-TB-MIC talk-back microphone that mutes the music while someone speaks, the WW-8CH-LD eight-channel line driver for boosting low-level RCA signals in multi-amplifier systems, and in-dash or under-dash mounts for the WS-420SQ EQ in black or silver.
The WS-G2-NMEA-20 adapter connects a WS-MC-20 to a NMEA 2000 network. Ask us which of these suits your system, as most are used only in larger or multi-zone setups. Tell us the head unit and amplifier you have so we can confirm compatibility.
Remotes are matched to a specific media centre, so confirm which one is in the boat.
Tower accessories and mounting
Clamps, X-Mounts, boat-specific brackets, covers and replacement grilles for tower speakers.
-
Clamps and X-Mount kits
Swivel, fixed and X-Mount hardware for REV, ICON and REV HD tower speakers.
These are the mounting parts for tower speakers: the ADP TC3-S swivel clamp, ADP TC3-F fixed clamp (with a silver aluminium option), a swivel surface mount (TC3-SXM), and X-Mount kits for REV/ICON and REV HD in black or white.
X-Mount kits convert a tower speaker for surface mounting on flat surfaces or select boat-specific adapters. Clamps fit round tower tubes. Pick by tower tube diameter or by the surface the speaker will sit on, and confirm the speaker model so the right kit is supplied.
-
Boat-specific tower brackets
Brackets sized for particular boats' towers.
These tower speaker brackets are made for specific boat towers. Listed models include Nautique (FC5-L, FC5-U, G, Z5 Drop 12, and the Flight Control Tower NAU-FCTA), Malibu G5-G, Supra FxONE, Gladiator-P (polished) and Illusion DXT.
Each is designed for factory-style alignment and a secure fit, giving a cleaner result than a generic clamp on towers with unusual shapes. Check the exact boat model and tower position (upper or lower, where relevant) before ordering, and let us know the year, as towers change between model years.
-
Speaker SuitZ covers
Neoprene covers to protect tower speakers in transport and storage.
SuitZ are neoprene covers with carrying handles, designed to protect tower speakers from scratches and dust during trailering, transport and off-season storage. They are model-specific, giving a close fit.
Sizes are SuitZ-8 (REV8 and ICON8), SuitZ-10 (REV 10), SuitZ REV 10 HD (for REV 10 HD and REV 12 HD) and Suitz REV 12 HD. They are useful if the speakers come off the tower between outings. Choose by speaker model and size. They also help keep the finish clean between outings, and the neoprene is soft enough not to mark gloss or matte paint. Tell us the speaker model and we will confirm the size.
-
Tower speaker grilles
Replacement grilles for REV and REV HD tower speakers.
Replacement and alternative grilles for tower speakers, including translucent grilles for REV 8 and REV 10, and XS, XW and XZ grilles for REV 10 HD and REV 12 HD in black or white.
They let you change the look of the speaker or replace a damaged grille. The translucent grilles are intended for use with LED lighting. Match the grille to the exact speaker and size, since REV and REV HD grilles are not interchangeable, and tell us the finish you want.
Tell us the boat make, model and year, as bracket fitment is boat-specific.
RGB lighting and controllers
LED rings, subwoofer RGB kits, strips and controllers to light up the Wet Sounds RGB range.
-
LED ring kits
RGB LED rings for coaxial speakers, tower speakers and subwoofers.
LED ring kits fit between a speaker and its mounting surface and add RGB lighting with pre-installed LEDs. Kits cover ZERO, RECON and REVO coaxials in 6.5″ and 8″, REV tower speakers in 8″ and 10″ (including Malibu versions), and 10″ and 12″ subwoofers.
Each is sized to the speaker, so match the diameter and model. RGB means red, green and blue LEDs that can be mixed into any colour. A compatible controller is required to change colours or sync the lights to the music.
-
Subwoofer RGB kits
RGB kits for REVO 8, 10 and 12 subwoofers.
Subwoofer RGB kits add lighting to REVO subwoofers in 8″, 10″ and 12″ sizes. They are separate from the subwoofer and are sold per size, so a sub can be fitted with lighting at the time of purchase or added later.
RGB means the light can be set to many colours. The kits need a compatible controller to change colours, and the REVO 12 PSE enclosure is already wired for RGB connections. Match the kit to your sub size. Tell us whether the lighting should run from an existing controller or a new one.
-
RGB controllers and amplifier
Controllers and an amplifier to drive Wet Sounds RGB lighting.
The RF-RGB-MC V2 is a wireless music-reactive controller with a touch remote that manages compatible Wet Sounds RGB lighting, adjusting colour, brightness and effects. The WWX-RGB-RS V3 is a single-zone rocker-switch controller. An RGB LED lighting amplifier is also listed for larger installs.
Choose the touch remote for effects and music sync, or the rocker switch for a simple wired control at the helm. Tell us how many lit speakers and subs are involved so we can size the controller and any amplifier correctly.
-
RGB strip, splitters and connectors
Strip lighting and connectors for building an RGB system.
A 5-metre (16.4 ft) marine RGB LED strip spool is available for undergunnels, towers and interior trim, on 12-volt systems. Connectors and splitters include a 4-pin waterproof splitter (1 male, 3 female), male and female 4-pin connector packs of ten, a connector kit and a 6-pin RGB connector.
These parts join lit speakers, strips and controllers into one system. Ask us if you need a layout worked out, and which connectors your speakers and controller use. The strip is cut and connected to suit the length of the area being lit.
RGB products need a compatible controller, so tell us what lighting you already have.
Subwoofer grilles
Replacement and upgrade grilles for REVO and ZERO subwoofers in several styles and colours.
-
REVO subwoofer grilles
SW, XW and XS grilles for REVO 8, 10 and 12 subwoofers.
Grilles for REVO free-air and HP subwoofers in 8″, 10″ and 12″. Styles are SW and XW (black or white) and XS stainless steel or XS (black, white, silver or gunmetal). Adapter grille kits (ADP XZ) fit the REVO 10 and 12 with ZERO-style XZ grilles in black or white.
They let you match the sub to the speakers and the look of the boat, or replace a damaged grille. Choose by subwoofer size and finish. Let us know the exact subwoofer model so the grille fits the frame.
-
ZERO XY yacht grilles
White yacht-style mesh grilles for ZERO 10 and 12 subwoofers.
White XY yacht-style grilles for ZERO Series subwoofers, offering a mesh look in 10″ and 12″ sizes. They suit boats with a more refined interior and match the XY yacht grilles supplied on some ZERO coaxial speakers.
Match the size to your ZERO subwoofer. Ask us if you would like the matching coaxial speakers in the same style, so the whole system looks consistent. They are white only, so they suit lighter interiors and white subwoofer enclosures. Tell us the sub size and we will confirm fitment before ordering.
Grilles are matched by subwoofer size and series.
Wet Wire, fuses and installation
Marine cable, fuses, RCA leads, connectors and kits for wiring an audio system.
-
Power and speaker wire
Frosted Wet Wire spools for power, speaker and RGB runs.
Wet Wire is Wet Sounds' marine-grade cable. Spools include 1/0GA and 4GA power cable in red and black, 12 and 14 gauge speaker wire, 18GA primary wire, a 22GA RGB wire spool and a combined speaker/RGB wire spool.
Gauge (GA) is wire thickness: a lower number is thicker and carries more current. Choose by the amplifier current and the length of the run, and use the combined speaker and RGB wire where lit speakers need both signals in one cable.
-
Fuses and fuse holders
ANL and Mini ANL fuses, holders and a distribution block.
ANL fuses in 250 and 300 amp, Mini ANL fuses in 25, 60, 100 and 150 amp (each as a four-pack), plus an ANL fuse holder, an ATC 8G holder and a fuse distribution block.
A fuse protects the power cable if a fault occurs, so it sits close to the battery. The rating follows the cable and the amplifier, so confirm it with us. The distribution block splits one power feed to several amplifiers, which is useful on larger systems with multiple amplifiers.
-
RCA cables and adapters
2- and 6-channel RCA leads, Y adapters and 3.5 mm adapters.
Signal cables include 2-channel RCA in 1.5, 5, 12, 17 and 23 ft lengths, 6-channel RCA in 5 and 23 ft, RCA Y adapters (male to two female, female to two male), RCA to 3.5 mm and 3.5 mm female to RCA mount adapters, and a 3-foot 3.5 mm aux cable.
RCA leads carry the low-level audio signal from the head unit to the amplifier. Pick the length for your helm-to-amplifier run, and the channel count to match the number of amplifier channels. Y adapters split one signal to two inputs.
-
Amp wiring kit
A complete single-amplifier wiring kit.
The WW-SINGLE AMP KIT supplies the power, ground, signal and protection parts for one amplifier installation, for marine, powersports and ATV systems. It is built for durability and steady electrical performance.
It is a convenient way to start an install with the main parts in one box rather than buying cable, fuse and connectors separately. Tell us the amplifier and we can confirm that the kit suits its current draw, or whether heavier cable is needed. The kit is intended for a single amplifier, so multi-amplifier systems need more than one or a separate distribution block.
Tell us the amplifier and run length so we can size the cable and fuse.
Other accessories
Antennas, connectors, adapters and small extras that complete an install.
-
WWX-ANTW marine antenna
An AM/FM antenna for marine media centres.
The WWX-ANTW is a marine AM/FM antenna for a head unit or media centre. A good antenna matters for radio reception on the water, where signals can be weak, especially away from the coast.
Ask us whether your media centre already has one, and which mounting spot suits the boat. Bluetooth, USB and other sources do not need an antenna, so it is only needed for radio listening. Mounting location affects reception, so position it as high and clear of metalwork as practical, and keep the cable away from power runs to reduce interference.
-
Speaker quick-release connectors
Lockable 4-post connectors and a retrofit kit.
A male and a female quick-release lockable 4-post marine connector, plus a speaker connector retro kit. They make it easy to unplug tower speakers when removing them for storage or trailering, and the locking design helps stop them working loose at speed.
The retro kit is used to convert existing speakers to the connector system. Match the connector to the speaker plugs you have, and tell us the speaker model if you are not sure which parts you need. They are sold as male and female halves, so order both sides if you are fitting a new run of wire.
-
USB, OEM and docking extras
A flush-mount USB, an OEM source adapter and BABz bumpers.
The WWX-USB-FM is a flush-mount USB socket with a 6 ft extension cable and cover. The ST-DC-OEM interfaces with factory Polaris Ride Command and Murphy head units, so Wet Sounds products can connect to them. WWX-POL-RC-ADAP is a Polaris Ride Command adapter. The WS-BABz bumper is a set of buoy-ball bumpers for docking protection.
These are small add-ons rather than core audio parts, so ask us about each and which suit your boat or vehicle before ordering. Compatibility depends on the head unit, so give us the make and model first.
Ask us if you are unsure which small part you need.
Wet Sounds build audio for boats rather than audio that happens to be on a boat. Their speakers, amplifiers, subwoofers and tower systems are made to stay intelligible over engine and wind noise, and to survive salt, sun and spray while doing it.
What we do with it
- Specify the system for the boat. Speaker count, placement and amplifier power depend on the deck layout and how the boat is actually used. A centre-console running offshore and a cruiser at anchor want different systems.
- Fit it properly. Cable runs, fusing and the draw on the house bank are part of the job, not an afterthought. Audio is one of the most common reasons a battery bank ends up undersized.
- Integrate it. Where the boat has a Raymarine display or a digital switching system aboard, the audio can be controlled from it rather than from a separate head unit.
Getting a price
Tell us the boat, roughly where the speakers should go and how loud you actually need it, and we will quote the system and the installation together. Call the shop or send an enquiry and we will come back with options at more than one price.
Send an enquiry or call the shop on +1 868 634-2203. Back to all brands.